×

MENU Resize to Fit-Double Tap Screen
Everything Boat Building
Don't tell me that I can't. Tell me how I can.
Disclaimer:   I am not a spokesperson for the US Coast Guard or ABYC. For an official interpretation of regulations or standards you must contact the US Coast Guard or other organization referenced..   More.....
The entire electrical section of this website may be purchased and downloaded. It is in PDF format and payment is through PAYPAL
Go to the store here
\$12.50 USD
If you know little or nothing about electrical circuits go to,
Basic Electricity  1   2   3   4   5   6   7   8   9   10   11   12   13   14   15   16

US Navy Basic Electricity Course

ABYC Basic Electrical Course

Contact ABYC and the Coast Guard to get the latest standards for Electrical systems.

# Go here for Print Friendly Page

## Basic Electricity - Page 4 - Simple Circuits

### Basic electricity for boat builders, boat repairers and owners. What you need to know about the electrical systems on your boat. Basic DC circuits. Power Source, conductors, fuses, switches, grounds.

There are some basic elements to every circuit. There is the source of power, the positive conductor, the negative or return conductor, a switch, overcurrent protection, and the load. See http://eschooltoday.com/science/electricity/what-is-an-electrical-circuit.html

Source of Power:

Generally the source of power is a battery or a battery bank. If the engine is running the source may be the alternator. For larger boats with many electrical devices it may be from an converter, or inverter, or from the shore power. Some boats also have an onboard auxiliary generator. A buss bar is considered the source of power for a specific circuit.

Conductors are generally wire or cable, but there are other conductors such as circuit boards, distribution boards or buss bars. The simplest circuit has a positive wire going to the load, and a negative wire coming back. However, this would hardly be practical because the power would always be on. So there are generally two other devices in a circuit.

Overcurrent Protection (Fuses or Circuit Breakers)

The first is a fuse or circuit breaker. See Marine Fuses and Circuit breakers.

This should be as close to the power source as possible because it's job is to protect the wire to the load.

Switches:

Then there is a switch to turn the device on or off. Here is a diagram of a simple circuit.

All DC circuits are based on this simple model.

Here is another simple circuit diagram that is slightly more detailed.

Ground:

As you can see the negative wire from the battery is connected to the outboard engine. It would be connected to the block if this were an inboard engine. This establishes the ground. See West Marine on Grounding Systems : https://www.westmarine.com/WestAdvisor/Marine-Grounding-Systems

Series Circuits: Remember those Christmas tree lights that when one light failed, they all went out?  Then you had to check every light on the string until you found and replaced the bad one? That's a series circuit. If it had been a parallel circuit the good lights would have still been lit. Genrally on boats there will be only one electrical item on a series circuit such as, a bige pump,  a cranking motor, or a blower.  If you have two or more, the voltage reduces at each item and you may not have a high enough voltage to run the equipment that is at the end. Also If there is a break in the circuit, or one item goes bad, they all stop working.

Parallel Circuits:

In a parallel circuit there may be many devices on the circuit.  As in the circuit diagram above, the navigation lights are in parallel.  On larger boats you may have several electronic items or instruments on a paralllel circuit.  The voltage stays the same in both legs of the circuit.  Resistance is reduced.  Plus if one item fails the others keep on working.

Series and Parallel Circuits:

Batteries are not the only electrical component that can be wired in series or parallel.  Electrical devices on a circuit can be wired in series or parallel as well. Parallel circuits are very common on boats, especially with lighting.  It decreases resistance on the circuit and decreases voltage drop; In the diagram above the navigation lights are in a Parallel Circuit. Most of the other items are in a series circuit. Below is a typical Parallel Lighting Circuit and a Series Lighting Circuit. Each has advantages and disadvantages.

Overcurrent Protection:

In the circuit diagrams above there is a fuse or circuit breaker near the battery. ABYC standards, Federal regulations, and ISO say it has to be within seven inches (17.8 cm)of the source of power. This protects the wire between the battery and the positive distribution buss.

This is an important point that is often misunderstood and needs to be repeated. Fuses and circuit breakers protect the wires, not the equipment. The danger is that the wire will get too hot, melt the insulation, and start a fire. Typical fuses:

If you look at the positive distribution buss, you will see that there is also overcurrent protection immediately after the buss.  That is because the buss is considered the source of power for the connected equipment. It too must be within seven inches of the buss bar. There are exceptions. See
Over Current Protection on Electrical Systems Page 1
https://newboatbuilders.com/mobile/elect_a.html

After that there is a switch to turn the equipment on or off. An exception is the bilge pump. Bilge pumps are usually wired directly. Most have a built in float switch, that turns the pump on when the water gets to a certain level and a bypass switch to turn it on manually.  Bilge pumps may have a small in-line fuse that protects the pump from burning out if something clogs the pick up and water stops flowing.

Below is a typical distribution buss bar. This one is in the negative or ground side of the circuit. The large wire connected to the bolt on the left end is the wire from the negative post on the battery.  All the other wires are negative wires to various pieces of equipment.

Neatness:

By the way, notice how neat and tidy and organized this is. Wiring should always be organized and neat. The only thing that would make this better is a tag or label for each wire naming what equipment it connects to.  Making your wiring neat and tidy accomplishes several things. It keeps wires from swinging and swaying and protects them from abrasion.  It also makes it far easier to trace out a circuit and find and correct problems.